{"product_id":"arrakis-simple-ip-8a-aoip-node","title":"Arrakis Simple-IP-8A AoIP Node","description":"\u003ch1\u003e\u003cstrong\u003eArrakis Simple-IP-8A AoIP Node\u003c\/strong\u003e\u003c\/h1\u003e\u003cp\u003eWhat This Arrakis Simple-IP-8A AoIP Node Actually Is This is the Simple-IP-8A, a compact Dante audio-over-IP node built to bring analog audio equipment onto a networked Dante system without complicated wiring or expensive infrastructure. It handles 8 mono inputs and 8 mono outputs, or you can configure it as 4 stereo inputs and outputs depending on how your sources are set up. Being AES67 and Dante compatible means it works within the broader networked audio ecosystem, not just with Arrakis gear specifically, so it plays well with other AES67-compliant equipment from manufacturers like Wheatstone, Telos, or Lawo if your studio uses a mix of brands. This node is the analog variant in the Simple IP lineup, meaning it's built specifically for connecting traditional analog audio gear, microphones, line sources, playback devices, and similar equipment, onto your Dante network using standard connectors rather than requiring digital-only sources. How the Simple-IP-8A Gets Your Analog Gear Onto a Dante Network The whole point of this node is removing the complexity most people associate with getting into networked audio. Instead of running miles of point-to-point cable or dealing with punch blocks between rooms, you connect your analog gear directly to the Simple-IP-8A, and from there your audio travels over standard Ethernet to anywhere else on your Dante network. Once connected, the node shows up automatically in Dante Controller within seconds, letting you route its inputs and outputs to any other Dante-enabled device on your system, whether that's a DARC Surface, a DARC Virtual software console, or any other compatible hardware. This is a genuinely simple way to bridge analog equipment into a modern networked studio without needing specialized networking knowledge or custom cabling runs between every piece of gear. Configuring Between 8 Mono and 4 Stereo Depending on Your Sources Because the Simple-IP-8A can be configured as either 8 mono inputs and outputs or 4 stereo inputs and outputs, you have real flexibility in how you use its available channels depending on what you're actually connecting. If you're bringing in individual microphones, mono line sources, or other single-channel gear, running the node in mono mode gives you the most available connections. If you're instead connecting stereo sources like a playback device, a stereo processor, or a pair of monitor outputs, switching to stereo mode groups your channels accordingly so each connection carries a full left and right signal. This flexibility means a single node can adapt to different studio needs without requiring you to buy separate hardware for mono versus stereo applications. Why Being AES67 and Dante Compatible Matters Dante has become one of the dominant standards for networked audio in broadcast and production environments, and AES67 compatibility extends that reach even further by letting the Simple-IP-8A talk to equipment outside the Dante ecosystem that follows the same open networking standard. This matters if your studio is mixing equipment from different manufacturers, since you're not locked into a single vendor's proprietary networking protocol just because you chose this particular node. It also future-proofs your investment somewhat, since AES67 compliance means this node will continue to work alongside a broader range of professional audio gear as your studio's equipment list grows or changes over time. Where the Simple-IP-8A Fits Into a Studio Network This node is commonly used to connect microphones, line-level playback devices, phone hybrids, or other analog studio gear into a larger AoIP system, whether that's a single-studio setup or a network spanning multiple rooms. It pairs naturally with Arrakis consoles like the DARC Surface or DARC Virtual software console, but since it's AES67 compatible, it also works as a bridge point for connecting existing analog consoles or outboard gear into a Dante network alongside other manufacturers' equipment. Because it's a relatively small, focused node rather than a large centralized audio router, it's also easy to place physically close to the equipment it's connecting, keeping analog cable runs short and reducing the noise and hum that longer runs can sometimes introduce. Who Should Be Adding a Simple-IP-8A to Their Setup This node is a solid fit for smaller studios or specific equipment clusters that need a manageable amount of I\/O without stepping up to a larger 16-channel node. It's especially useful for stations building out a network gradually, since you can add Simple-IP-8A units incrementally as you connect more analog gear rather than committing to a large centralized system all at once. Studios mixing analog equipment with newer Dante-native gear will find this node particularly valuable, since it lets older or non-networked equipment participate in a modern AoIP setup without needing to be replaced. For anyone running an Arrakis DARC console system, or any other AES67-compatible broadcast platform, this is a practical, flexible way to bring analog sources onto your network.\u003c\/p\u003e","brand":"Arrakis","offers":[{"title":"Default Title","offer_id":50995706855671,"sku":"Simple-IP-8A","price":2199.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0422\/1291\/7402\/files\/Arrakis-SIMPLE-IP-8-A.jpg?v=1785795342","url":"https:\/\/www.305broadcast.com\/products\/arrakis-simple-ip-8a-aoip-node","provider":"305broadcast","version":"1.0","type":"link"}